Line 35 in the script (./arduino) was: "$JAVA" manually browsed about 10 of the 1100 pages or so of the forum "Installation and Troubleshooting". The list command ($ls -l) reported the following details for that file: The file ‘java’, which the above script reported, was present. The tablet was restarted, but still no icon observed.Īnother option to start the IDE by command line (./arduino) was found which resulted in the following report, but there was still no IDE window:Īrduino: line 35: /data/data/com.termux/files/home/github/software/arduino/arduino-1.8.9/java/bin/java: No such file or directory ![]() The Android does not do sudo the last I knew. One forum indicated the softlink error could be ignored ( can't install IDE on Ubuntu - Installation & Troubleshooting - Arduino Forum). Ln: failed to create symbolic link '/usr/local/bin/arduino': No such file or directoryĪdding symlink failed. Rm: cannot remove '/usr/local/bin/arduino': No such file or directory The reports were as follows:Īdding desktop shortcut and menu item for Arduino IDE. The script did complete quickly, but there were reports about a symbolic link, and no icon was observed on the “tablet’s desktop”. Tar: can't create hardlink 'arduino-1.8.9/hardware/tools/avr/bin/avr-gcc-5.4.0' to 'arduino-1.8.9/hardware/tools/avr/bin/avr-gcc' ![]() The extraction processes reported the following, which was skipped over: At least one forum discussion said downloading the wrong option caused operator troubles, so all 4 were tried, but no icon each time, and the same results below for each option. Downloaded all 4 options, with with same install result in each instance. Tried the Linux install procedures at with the following outcomes: The tablet has ARM processor(s), 64 bit, but running in 32 bit mode, according to another app (AIDA64) If all else fails, don't give up the world of IT and Cyber security is amazing.Operated a Linux app (Termux) on a Samsung Android tablet (tab A). You also might need to look into rfkill (radio frequency kill), and unblock your network adapter by sudo rfkill unblock all sudo rfkill unblock wifi (run command a few times, and restart PC) If you didn't bring your network card wlan0 back up before running reaver, restart your PC and try again. If it still is not working, the order of precedence with the above commands matters. You may also want to try: sudo ifconfig wlan0 sudo ifconfig wlan0 down sudo ifconfig wlan0 up If that is not successful, try restarting your PC (at bootup if you have a wireless switch on your PC switch it on now), and repeating the above command. The command is usually: sudo ifconfig wlan0 up sudo rfkill unblock all sudo rfkill unblock wifi ![]() INFO: If there is a hardware switch that controls your network adapter switch it on before executing the following command ![]() You may have not properly brought up your wireless network adapter wlan0 You should restart your computer, run the above commands to configure your network adapter, and rerun reaver. Verify that you put wlan0 up before you try running reaver INFO: The network card ("wifi card") that's in your PC may not even support packet injection, or monitor mode.Īlso make sure that if you put wlan0 into monitor mode you run these commands: sudo ifconfig wlan0 down Also your on an HP notebook that was built to run Windows 10, you would need to live boot from a USB or CD, and try configuring your network adapter with ifconfig then, also your wireless network adapter might have a different name other than wlan0 (Kali configures this). If you're running Linux in a virtual container you need an external wireless card. Inet6 fe80::51e1:4e13:b623:444b prefixlen 64 scopeid 0x0Īre you running Kali, or any other Linux distribution inside of Virtualbox, VMWare? TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 So I do ifconfig and get (running internet off phone) eth1: flags=41 I'm trying to use reaver and when I attempt it says Failed to retrieve a MAC address for interface 'wlan0'! I've tried all the other threads and nothing is working.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |